12698484
HITACHI 12698484 Pompe Haute Pression GM Buick Cadillac CT4 CT5 2.0T LSY 350 bar
12683985, 12694539, 12708365, HFS034-135Integrated Pulse-Width Modulated Electric Spill Valve (SCV)-350 barCompatibilité véhicules et motorisations
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Manufacturer | Hitachi Astemo / General Motors Genuine Parts |
| System Technology | 350 bar (35 MPa / 5076 psi) Ultra-High Pressure SIDI Mechanical Pump |
| Drive Cam Element | Camshaft Follower Roller Lifter (GM 12674744) on Exhaust Cam |
| Mounting Flange Fastener Torque | 12 N·m + 45° Torque-To-Yield (TTY) M6 Bolts |
| High Pressure Pipe Joint Torque | 32 N·m Flare Nut Connection |
| Soupape de commandeSpéc. clé | |
| Codes défauts fréquents | P0087 (Fuel Rail Pressure Low), P0089 (Fuel Pressure Regulator Performance), P016F |
| Common Symptoms | High-pressure fuel odor in oil filler cap, rising crankcase oil level, check engine light & hesitations under load |
| Pression de serviceSpéc. clé |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- [
- {
- "step": 1,
- "title": "Relieve 350 bar High-Pressure Fuel Rail",
- "instruction": "Disconnect fuel pump control module (FPCM) harness. Crank engine for 10 seconds. Check GDS2 scan tool to verify fuel rail pressure is below 1 MPa."
- },
- {
- "step": 2,
- "title": "Inspect Engine Oil for Gasoline Dilution",
- "instruction": "Check dipstick and oil filler cap. If oil smells strongly of gasoline or viscosity has degraded due to pump shaft seal leakage, replace engine oil and filter."
- },
- {
- "step": 3,
- "title": "Inspect Roller Lifter Tappet GM 12674744",
- "instruction": "Slide out roller lifter from cylinder head. Inspect roller bearing for pitting or flat spots. Coat lifter in clean engine oil prior to reinsertion."
- },
- {
- "step": 4,
- "title": "Torque Pump Flange Bolts to TTY Spec",
- "instruction": "Set camshaft drive lobe to low circle. Hand-start new TTY flange bolts. Tighten evenly in alternating stages to 12 N\u00b7m, then apply a final 45-degree angle turn."
- },
- {
- "step": 5,
- "title": "Connect High-Pressure Hard Line & Torque",
- "instruction": "Align high-pressure delivery pipe into pump outlet. Hand-tighten flare nut squarely, then torque flare fitting to exactly 32 N\u00b7m."
- }
- ]
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.