68318470AA
BOSCH 68318470AA Injecteur Haute Pression Jeep Wrangler JL Alfa 2.0L Hurricane
68318470AB, 0261500448, 0261500449, 50052349Multi-Hole Laser Drilled Solenoid Actuated Direct Injection Nozzle-200 barCompatibilité véhicules et motorisations
| Véhicule | Moteur | Années |
|---|---|---|
| Jeep Wrangler JL 2.0T | 2.0L GME T4 Hurricane 200kW | 2018-2024 |
| Jeep Grand Cherokee 2.0T 4xe | 2.0L GME T4 Hybrid 280kW | 2022-2024 |
| Alfa Romeo Giulia 2.0T | 2.0L GME MultiAir 206kW | 2017-2024 |
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Type de système | Bosch HDEV5 Multi-Hole Direct Gasoline Fuel Injector |
| Pression de serviceSpéc. clé | |
| Spray Pattern | Asymmetrical 6-orifice pattern engineered for deep chamber penetration |
| Fuel Rail Bolt Torque | 12 N·m (holding bracket fasteners) |
| High Pressure Pipe Torque | 27 N·m Flare Nut Connection |
| Coil Resistance | 1.4 - 1.8 Ω at 20°C (High performance peak-and-hold excitation) |
| Codes défauts fréquents | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0172 (Fuel System Rich Bank 1) |
| Workshop Precaution | Install new Teflon combustion tip seals using expanding mandrel and sizing collar |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- [
- {
- "step": 1,
- "title": "Relieve Fuel System Residual Pressure",
- "instruction": "Depressurize high pressure fuel system using diagnostic scan tool or fuel pump relay isolation. Disconnect battery negative terminal."
- },
- {
- "step": 2,
- "title": "Disconnect Wiring Harness & Fuel Rail Hard Lines",
- "instruction": "Unclip wiring harness from all four injectors. Loosen the high pressure fuel crossover pipe (27 N·m) and unbolt fuel rail fasteners (12 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Fit New Teflon Chamber Seals",
- "instruction": "Use slide hammer tool to extract direct injectors from cylinder head. Install new blue Teflon seals using calibration guide sleeves."
- },
- {
- "step": 4,
- "title": "Torque Rail Fasteners & Verify High Pressure Seal",
- "instruction": "Seat injectors into cylinder ports. Torque rail bolts to 12 N·m. Tighten steel high pressure line to 27 N·m. Prime fuel system and check for leaks."
- }
- ]
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.