68318470AA
BOSCH 68318470AA Hogedrukinjector Jeep Wrangler JL Alfa 2.0L Hurricane GDI
68318470AB, 0261500448, 0261500449, 50052349Multi-Hole Laser Drilled Solenoid Actuated Direct Injection Nozzle-200 barVoertuig- & motortoepassingen
| Voertuig | Motor | Bouwjaren |
|---|---|---|
| Jeep Wrangler JL 2.0T | 2.0L GME T4 Hurricane 200kW | 2018-2024 |
| Jeep Grand Cherokee 2.0T 4xe | 2.0L GME T4 Hybrid 280kW | 2022-2024 |
| Alfa Romeo Giulia 2.0T | 2.0L GME MultiAir 206kW | 2017-2024 |
Technische specificaties
| Specificatie | Waarde |
|---|---|
| Systeemtype | Bosch HDEV5 Multi-Hole Direct Gasoline Fuel Injector |
| WerkdrukKernspecificatie | |
| Spray Pattern | Asymmetrical 6-orifice pattern engineered for deep chamber penetration |
| Fuel Rail Bolt Torque | 12 N·m (holding bracket fasteners) |
| High Pressure Pipe Torque | 27 N·m Flare Nut Connection |
| Coil Resistance | 1.4 - 1.8 Ω at 20°C (High performance peak-and-hold excitation) |
| Veelvoorkomende foutcodes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0172 (Fuel System Rich Bank 1) |
| Workshop Precaution | Install new Teflon combustion tip seals using expanding mandrel and sizing collar |
Passende hogedrukbrandstofpomp (Brandstofcircuitmontage)
Werkt op hetzelfde hogedruk-common-railcircuit. Controleer bij raildrukverlies (P0087) de pompopbrengst voordat u injectoren vervangt.
Montagetips
- [
- {
- "step": 1,
- "title": "Relieve Fuel System Residual Pressure",
- "instruction": "Depressurize high pressure fuel system using diagnostic scan tool or fuel pump relay isolation. Disconnect battery negative terminal."
- },
- {
- "step": 2,
- "title": "Disconnect Wiring Harness & Fuel Rail Hard Lines",
- "instruction": "Unclip wiring harness from all four injectors. Loosen the high pressure fuel crossover pipe (27 N·m) and unbolt fuel rail fasteners (12 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Fit New Teflon Chamber Seals",
- "instruction": "Use slide hammer tool to extract direct injectors from cylinder head. Install new blue Teflon seals using calibration guide sleeves."
- },
- {
- "step": 4,
- "title": "Torque Rail Fasteners & Verify High Pressure Seal",
- "instruction": "Seat injectors into cylinder ports. Torque rail bolts to 12 N·m. Tighten steel high pressure line to 27 N·m. Prime fuel system and check for leaks."
- }
- ]
Foutcodes (DTC) & Diagnoseprotocollen
Veelvoorkomende diagnostische foutcodes (DTC's) die optreden wanneer deze common rail-injector slijtage, circuitstoringen of kalibratieafwijkingen vertoont:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Technische Diagnose- & Serviceprotocollen
Geverifieerde werkplaatsprocedures, testdrempels en richtlijnen voor deze component.