P0201: Spridarkrets felfunktion - Cylinder 1
Motorstyrenheten (ECM) detekterar ett avbrott, en kortslutning eller onormal strömförbrukning i cylinder 1:s spridarmagnetventil eller piezoaktuator.
🚗 Körsäkerhet, typiska reparationskostnader & kontroll
- 01
🚦 Körsäkerhet och mekanisk risk
Omedelbar mekanisk bedömning och behov av bärgareAvbrott/kretsfel i cylinder 1:s spridarkrets - Halta-hem-läge på 3 cylindrar
Den elektriska styrkretsen till cylinder 1:s spridare har ett avbrott eller en kortslutning. Cylinder 1 genererar ingen förbränningseffekt. Motorn vibrerar kraftigt vid gång på 3 cylindrar. Kör försiktigt i nödläge till närmaste verkstad.
MEKANISKA RISKER FÖR MOTORN VID FORTSATT KÖRNING:Kraftiga torsionssvängningar som kan skada dubbelmassesvänghjulet (DMF), pulseringar bakåt i insuget samt termisk överbelastning av katalysatorn. - 02
💰 Typisk verkstadsbudget
Förväntade kostnadsnivåer för reservdelar och arbeteLitet underhåll / Filter300 - 700 SEK (Byte av uppglappat 2-poligt kontaktstycke/pigtail till spridare eller justering av stiftspänning)Rengöring av givare, bränslefilterbyte, säkringskontroll eller kontaktstiftsrengöring.
Byte av ventil / Sensor1 400 - 3 000 SEK (Reparation av kablage/ledningsnät eller åtgärd av spridarspolens kontaktfel)Byte av enskild komponent (tryckreglerventil, doseringsventil eller renoverad spridare).
Större översyn / Pump och spridare4 000 - 8 500 SEK (Byte till fabriksrenoverad common rail-spridare inklusive ny kalibreringskodning/IMA-kod)Översyn av högtryckspump, ny OEM-spridaruppsättning eller byte av DPF-enhet.
- 03
🧰 Snabb visuell kontroll utan verktyg
5-minuters garagekoll innan du ringer verkstaden1Demontera motorkåpan i plast och lokalisera spridare 1 (närmast kamremmen/motorns framkant).2Vicka försiktigt på det 2-poliga kontaktstycket på spridare 1: Om tomgången omedelbart stabiliseras har kontakthylsorna tappat klämkraften och glappat upp.3Inspektera kablaget där det passerar vassa metallfästen: Kontrollera om kabelisoleringen skavts sönder eller kortsluter mot gods. - 04
🛡️ Skydd mot feldiagnoser på verkstad
Konkreta frågor till mekanikern för att undvika onödiga komponentbyten"Säg till verkstaden: 'Var god gör ett dragtest på kontakthylsorna i spridarkontakten och mät spolresistansen (0.2-0.5 ohm för magnetventil, 180-200 kOhm för piezoaktuator) innan ni offererar en ny motorstyrenhet eller byte av alla 4 spridare.'"
Teknisk anmärkning: Ställ dessa tekniska frågor till mekanikern innan du godkänner dyra offerter:
30-sekunders verkstadstriage
- Severe single-cylinder dead misfire
- Rhythmic engine knocking and rough idle
- Loss of highway cruising power
- Broken wire or high resistance in Cylinder 1 injector circuit
- Burnt or shorted injector solenoid coil
- Defective piezo ceramic crystal stack inside injector
Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.
The $1,200 Workshop Blunder: Replacing a $400 Injector or $1,500 ECM for a Spread Connector Terminal or Harness Rub
When P0201 is logged alongside violent single-cylinder misfiring and dead-pedal limp mode, technicians often rush to replace the Cylinder 1 common rail injector ($350 - $650) or condemn the Engine Control Module ($1,200 - $2,500) without performing pin drag or back-probe tests.
Over 40% of electrical injector circuit codes (P0201-P0204) are caused by spread, fatigued female terminal pins inside the injector wiring harness plug (especially on GM Duramax 6.6L FICM harnesses, Ford 1.6/2.0 TDCi, and VW 2.0 TDI) or wiring insulation chafing against the aluminum cylinder head or EGR bracket, producing intermittent resistance changes under engine vibration.
Perform a 'Terminal Drag Test' using a clean, new male test pin into the harness connector: verify snug, positive friction retention. Next, perform a fast cross-swap: move the suspected Cylinder 1 injector to Cylinder 2. Clear codes and restart the engine. If the code shifts to P0202, the injector coil or internal piezo crystal is physically open/shorted. If the code remains stubbornly locked on P0201, the injector is 100% healthy, and the fault lies entirely in the wiring harness, terminal tension, or ECM driver MOSFET.
Mest påverkade motorer och insprutningssystem
Denna felkod påverkar främst följande diesel common rail-plattformar. Kontrollera din motorfamilj nedan för kända felmönster och artikelnummer:
GM 6.6L Duramax Diesel (LLY, LBZ, LMM)
Bosch Solenoid CRIKänt fabriksfel: Known 'ice pick' failure: Cylinder 2 and 7 (and Cylinder 1 on LLY) injector harness plugs vibrate loose. Tensioning female pins fixes 90% of cases.
GM 98018449 / PT2162BMW 2.0d / 3.0d M47N, M57N (E46, E90, E60)
Bosch CRI2 / CRI3Känt fabriksfel: Oil soaked harness under intake manifold causing dielectric breakdown; injector internal coil connector vibration fretting.
13537790093 / 0445110131Renault / Dacia / Nissan 1.5 dCi (K9K)
Delphi / Continental DFPKänt fabriksfel: Note: In Renault systems Cylinder 1 is at flywheel/gearbox side, NOT the timing belt side. Misidentifying cylinder location causes wrong part replacement.
1660000Q0A / 28232248PSA / Ford 1.6 HDi / TDCi (DV6ATED4 / DLD-416)
Bosch CRI2.1Känt fabriksfel: Wiring loom rubs against metal alternator/fuel filter support bracket, causing intermittent short-to-ground.
0445110239 / 1980J4P0201-P0204 Injector Circuit Diagnosis Guide
Workshop troubleshooting guide for OBD-II codes P0201 to P0204 (Cylinder 1-4 Injector Circuit Malfunction). Resistance test specs, harness checks, and ECU driver stage.
Styrkrets & Ställdonslogik
1. Dynamic In-Demand Fuel Metering
Common rail diesel injectors rely on microsecond electrical actuation commands generated by high-side and low-side driver circuits inside the Engine Control Module (ECM). Injector actuators fall into two distinct physical technologies: Electromagnetic Solenoid (Bosch CRI1/CRI2/CRIN, Delphi DFI1, Denso G2) and Piezoelectric Ceramic Stack (Bosch CRI3/Piezo, Continental/VDO, Denso G3P). Both types actuate internal hydraulic control valves that unbalance needle pressure and initiate high-pressure injection.
2. Closed-Loop PID Deviation Monitoring
To overcome 2,000+ bar fuel pressure holding the needle on its seat, the ECM applies an ultra-fast high-voltage boost phase (typically 60V-80V for solenoids; 140V-200V for piezo crystals) with high peak current (15A-25A) to pull the control valve open within 150-200 microseconds. Once open, the ECM switches to a low-voltage pulse-width-modulated (PWM) hold phase (typically 12V-14V, 8A-12A) to sustain injection duration. The ECM monitors current feedback through internal sense resistors. DTC P0201 is logged when the measured current is either zero (open circuit), exceeds peak threshold limits (short circuit), or fails to collapse within specified decay time.
3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves
Diagnostic Trap: Solenoid (0.2-0.5 Ω) vs Piezo (180-220 kΩ) Testing Hazards. Never use a standard multimeter diode test or connect direct 12V battery power to a Piezo injector! Piezo crystals act as high-voltage capacitors. Injecting external direct current will permanently shatter the brittle crystal ceramic layers. Conversely, a piezo injector holding a residual 140V charge can deliver a painful electric shock to technicians touching bare terminal pins. Always use a dedicated high-voltage insulation megohmmeter (>500V test) to check for piezo insulation breakdown to the injector body.
Elektriska & Hydrauliska referensvärden
Steg-för-steg Felsökningsprotokoll
Swap Injector Test
Swap Injector 1 with Injector 2; clear codes and test-drive. If fault moves to P0202, injector is defective. If fault stays at P0201, harness or ECM is bad.
Coil Resistance & Continuity
Measure Injector 1 coil resistance directly at injector terminals; compare against healthy adjacent cylinders.
Oscilloscope Current Ramp
Clip current probe on Injector 1 wire; capture current ramp (look for sharp peak ~15A-20A for solenoid or rapid charge curve for piezo).
Recode New Injector
Install replacement injector and enter the alphanumeric IMA/C2i/C3i correction code into the ECM.
Hårdvarureparation och stycklista för komponenter
Isolate sub-assembly wiring and terminal wear before purchasing complete replacement injectors or control units using OEM/Tier-1 part numbers:
1-967644-1 / PT-BOSCH-2PTE Connectivity / AMP
OEM sealed 2-pin female connector pigtail with high-temperature silicone seals and gold-plated copper alloy terminals.
0445110369 / 0445110239Bosch
Factory calibrated common rail solenoid injector with microsecond closing latency and 1600-1800 bar operating ceiling.
0445115068 / 0445116029Bosch Piezo
Multi-layer piezoelectric ceramic crystal stack (180-220 kΩ) with integrated thermal compensation mechanism.
F00VP01004 / 1.5mm - 2.0mmBosch / Elring
Annealed OFHC copper combustion sealing washer preventing combustion gas blow-by and injector coil overheating.
Interaktiv toleransberäknare för Common Rail
Tillhörande bränslesystemkomponenter
The following genuine OEM fuel pumps and common rail injectors are verified factory equipment for engines reporting fault protocol P0201. Cross-reference operating pressures and tightening torques before sub-assembly replacement:
0445110131BOSCH
BOSCH 0445110131 Common Rail Injector for BMW 320d / 330d / 530d / 730d / X5 M47N & M57N Euro 3
View Technical Specs & Fitment →0445110239BOSCH
0445110239 Injector: PSA 1.6 HDi Ford 1.6 TDCi Specs
View Technical Specs & Fitment →095000-5880Denso
095000-5880 Denso Toyota 2KD-FTV Injector: 23670-30050 Data
View Technical Specs & Fitment →28337917Delphi
28337917 Delphi Bobcat D24 Injector: 7030364 Specs & Data
View Technical Specs & Fitment →095000-8340Denso
095000-8340 Denso Mitsubishi 4D56 HP Injector: 1465A367 Data
View Technical Specs & Fitment →0445120289Bosch
0445120289 Bosch Perkins 1104D Injector: 2645A749 Data
View Technical Specs & Fitment →Återställning av pumpinläring och provkörning
Following injector replacement for DTC P0201, the unique alphanumeric calibration code (Bosch IMA, Delphi C2i/C3i, or Denso QR) must be programmed into the ECM memory:
1. Scan Tool IMA Coding: Navigate to ECM Special Functions -> 'Injector Calibration Coding'. Enter the 6-to-30-character alphanumeric code laser-etched onto the plastic terminal head of the new injector.
2. Verify Checksum: Ensure the scan tool validates the mathematical checksum. Entering an incorrect code will distort fuel timing by up to 3 crank degrees and cause chronic knock or DPF soot overload.
3. Zero Fuel Calibration (ZFC) Relearn: Start the engine and drive until coolant temperature exceeds 80°C. Perform three continuous coast-down decelerations in high gear from 60 mph to 25 mph without touching the clutch or brake pedals. This teaches the ECM the exact physical needle closing latency for Cylinder 1.
Differentialdiagnos & Relaterade felkoder
Injector Circuit Malfunction - Cylinder 2
Identical electrical circuit fault on Cylinder 2; used for cross-swapping diagnosis to isolate whether the failure follows the injector or stays with the harness.
Injector Circuit Malfunction - Cylinder 3
Companion cylinder circuit fault in 4-cylinder firing order (1-3-4-2).
Injector Circuit Malfunction - Cylinder 4
Opposing bank cylinder circuit fault; frequently triggered alongside P0201 when the ECM disables Bank 1 driver stage.
Cylinder 1 Injector Circuit Low
Direct circuit short to ground on Cylinder 1 injector low-side control line.
Cylinder 1 Injector Circuit High
Direct short to vehicle battery voltage on Cylinder 1 injector circuit.
Cylinder 1 Contribution/Balance Fault
Mechanical kinetic consequence of P0201: crankshaft sensor detects zero angular acceleration from Cylinder 1.
Verkliga verkstadsfall
Vanliga tekniska frågor
Vad betyder felkoden P0201?
Motorstyrenheten (ECM) detekterar ett avbrott, en kortslutning eller onormal strömförbrukning i cylinder 1:s spridarmagnetventil eller piezoaktuator.
Vilka är de vanligaste symtomen på P0201?
Severe single-cylinder dead misfire, Rhythmic engine knocking and rough idle, Loss of highway cruising power, Exhaust smoke (white or unburnt diesel puffing).
Vad orsakar P0201 på en dieselmotor?
Broken wire or high resistance in Cylinder 1 injector circuit; Burnt or shorted injector solenoid coil; Defective piezo ceramic crystal stack inside injector; Loose or spread connector terminal pin on Injector 1.
Är det säkert att köra med felkod P0201 aktiv?
🔴 Kritiskt: Kör ej vidare / Bärgning krävs
Vad kostar det att åtgärda felkod P0201?
Typiska reparationskostnader för felkod P0201 beror på den bakomliggande orsaken och diagnostiknivån: Nivå 1 (Mindre underhåll / Gör-det-själv): 300 - 700 SEK (Byte av uppglappat 2-poligt kontaktstycke/pigtail till spridare eller justering av stiftspänning) (Rengöring av givare, bränslefilterbyte, säkringskontroll eller kontaktstiftsrengöring.); Nivå 2 (Komponentbyte): 1 400 - 3 000 SEK (Reparation av kablage/ledningsnät eller åtgärd av spridarspolens kontaktfel) (Byte av enskild komponent (tryckreglerventil, doseringsventil eller renoverad spridare).); Nivå 3 (Större delsystem): 4 000 - 8 500 SEK (Byte till fabriksrenoverad common rail-spridare inklusive ny kalibreringskodning/IMA-kod) (Översyn av högtryckspump, ny OEM-spridaruppsättning eller byte av DPF-enhet.). Verkstadsriktpriser. Mer än 70 % av fallen åtgärdas inom nivå 1 eller 2 utan att hela delsystem behöver bytas.
Can I test a diesel piezo injector with a normal multimeter?
You can measure resistance across the two pins with a high-grade digital multimeter (a healthy piezo typically reads 180 to 220 kΩ), but this alone will NOT prove the injector is good. Piezo crystal failure almost always manifests as high-voltage insulation breakdown under actual operating voltages (140-200V). To properly test a suspected piezo injector, use an insulation resistance tester (megohmmeter) set to 250V or 500V between either pin and the injector metal body: the insulation resistance must exceed 10 MΩ. Anything below 10 MΩ indicates internal crystal breakdown.
Why did my engine shut down completely when only Cylinder 1 injector failed (P0201)?
Modern diesel ECMs (such as Bosch EDC17 and Continental SID) group injectors into shared high-voltage capacitor driver banks (typically Cylinders 1-4 on Bank 1, Cylinders 2-3 on Bank 2). When Cylinder 1 injector suffers a short circuit or ground fault, the excessive current threatens to burn out the ECM's internal power transistors. To save itself from catastrophic destruction, the ECM shuts down the entire bank of injectors, turning a single-cylinder fault into a complete engine shutdown or severe two-cylinder shutdown.
How can I tell if P0201 is caused by the injector itself or the engine wiring harness?
Disconnect the Cylinder 1 and Cylinder 2 injector electrical connectors. Swap Injector 1 with Injector 2 physically (or swap the harness connectors if length permits on test benches), clear the fault codes, and crank the engine. If the fault moves to Cylinder 2 (P0202), the injector itself is defective. If the fault remains locked on Cylinder 1 (P0201), the problem is in the wiring harness, connector terminal tension, or the ECM internal driver stage.
What does code P0263 mean when it appears alongside P0201?
P0263 indicates 'Cylinder 1 Contribution/Balance Fault'. While P0201 is an electrical circuit code (the ECM cannot see proper current flowing through the coil), P0263 is a mechanical/kinetic code detected via the crankshaft position sensor (the crankshaft did not accelerate as expected during Cylinder 1's power stroke). When P0201 prevents Cylinder 1 from firing, P0263 naturally follows because Cylinder 1 produces zero torque output.