MOPAR
05038533AA
Visa spec.
SolenoidChrysler Multi-Port Electronic Fuel Injection (MPI / EFI 58-psi System)Euro 255
MOPAR 05038533AA Bränsleinjektor Dodge Ram 1500 Jeep 5.7L HEMI V8
OE-REFERENS
68211173AA, 05038533AB, 5038533AA, RL038533AA, 280158233, FJ1080, 0280158233STYRVENTIL
High-Efficiency 4-Hole Precision Atomization Director PlateSPRIDARSPETS
4-Hole Precision Calibrated Stainless Steel Director PlateRAILTRYCK
4.0 barMILJÖKLASSTier 2 Bin 5 / Euro 5 / LEV II
GARANTI12 Månader
02
Passande fordon & motorer
| Fordon | Motor | Årsmodell |
|---|---|---|
| Ram Ram 1500 / 2500 5.7L HEMI | Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC) | 2009-2024 |
| Dodge Durango 5.7L HEMI | Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC) | 2009-2024 |
| Dodge Charger / Challenger | Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC) | 2009-2023 |
| Jeep Grand Cherokee (WK2) 5.7L HEMI | Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC) | 2009-2023 |
| Chrysler 300 / 300C 5.7L HEMI | Chrysler/Dodge 5.7L HEMI V8 OHV 16-Valve VVT MDS (Eagle Architecture, EZH/EZC) | 2009-2023 |
03
Tekniska specifikationer
| Specifikation | Värde |
|---|---|
| Systemtyp | Chrysler Multi-Port Electronic Fuel Injection (MPI / EFI) System |
| Operating Fuel Pressure | 4.0 bar (58 psi / 400 kPa regulated) |
| Static Flow Rate | 34.8 lb/hr @ 58 psi (365 cc/min @ 400 kPa) |
| Electrical Resistance | 12.0 - 14.5 Ohms @ 20°C (High-Impedance Saturated Solenoid) |
| Nozzle AtomizerHuvudspec. | |
| Fuel Rail Fastener Torque | 9 N·m (80 in-lb) composite intake manifold rail bolts |
| Upper & Lower O-Rings | High-Durability Fluorosilicone (FKM) Viton Material |
| Manufacturer | Bosch / Mopar (Tier-1 OEM for Stellantis / Chrysler Group LLC) |
| Bosch Production Reference | 0280158233 |
| ArbetstryckHuvudspec. |
04
Monteringsanvisningar
Tips & varningar:
- Never use petroleum jelly or brake cleaner on O-rings: Use clean engine oil or silicone spray; harsh solvents degrade Viton fluorosilicone causing intake manifold air leaks.
- Inspect intake manifold injector pockets: Remove grit and carbon buildup from the composite manifold injector bores before pressing new injectors in to ensure airtight vacuum sealing.
- Verify injector retaining clip alignment: Ensure injector clips snap into the recessed groove on both the injector body and the rail collar to prevent pressure blow-off.
- Check for fuel leaks before restarting: Cycle key to RUN position three times without cranking to pressurize system to 58 psi and inspect rails for weeping.
05
Felkoder (DTC) och Diagnosprotokoll
Vanliga diagnosfelkoder (DTC) som aktiveras nar denna common rail-injektor uppvisar slitage, kretsfel eller kalibreringsavvikelse:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
VERKSTADSMANUALER
Tekniska Diagnos- och Serviceprotokoll
Verifierade verkstadsrutiner, testgränsvärden och serviceinstruktioner för denna komponent.
Diagnostikprotokoll för verkstad
Läs tekniskt protokollTest av Returläckage på Common Rail-Spridare: Gränsvärden
VERKSTADS-SOP FÖR COMMON RAIL-DIESEL
Läs tekniskt protokollFastbrända spridare: Utdragning & koksrengöring | SOP
MONTERINGS- OCH INSTALLATIONSPROTOKOLL
Läs tekniskt protokoll