ENGINE FAMILY SPECIFICATIONBOSCH COMMON RAILEuro 5

Hino J05E / J08E (5.1L / 7.7L) Diesel Injector
Cross-Reference & Technical Specs

Authoritative technical specifications, verified Bosch part numbers, control valve stamping codes, nozzle spray orifices, and hold-down tightening torque for the Hino J05E / J08E diesel engine family.

Primary OEMBOSCH
Control ValveF00RJ02397
Nozzle CodeDLLA153P2238
Peak Pressure2000 bar peak rail pressure
Hold-Down Torque30 N·m
01

All Verified Part Numbers for Hino J05E / J08E (5.1L / 7.7L)

The following 3 common-rail injector assemblies are calibrated for this engine family. Click any SKU to view individual test bench flow curves, sister cross-references, and vehicle applications.

Part Number (SKU)Primary OE ReferenceControl ValveNozzle Code
23670-E0490F00RJ02397DLLA153P2238
23670-E0050, VH23670E0050, 095000-6350PLATE 10# / DENSO G2 VALVE PLATEDLLA155P848
095000-6590, 095000-6591, 095000-6592PLATE 10# / DENSO G2 VALVE PLATEDLLA155P868
02

Verified Vehicle Compatibility

Make / ManufacturerVehicle Model & PlatformEngine SpecificationModel Years
Hino300 SeriesJ05E / J08E2011-
HinoDutroJ05E / J08E2011-2019
Hino500 / 600 SeriesJ05E / J08E2012-
ToyotaCoasterJ05E / J08E2012-
Hino238 / 258 / 268 / 338J05E / J08E2010-
Hino155 / 195J05E / J08E2013-2020
KobelcoSK200-8 / SK200LC-8J05E / J08E2006-2015
KobelcoSK210 / SK210LC (Gen 8)J05E / J08E2006-2015
KobelcoSK250-8 / SK260-8J05E / J08E2006-2015
KobelcoSK330-8 / SK350-8J05E / J08E2006-2015
New HollandE215B / E245BJ05E / J08E2007-2016
Hino500 Series / RangerJ05E / J08E2005-2016
KobelcoSK330-8 / SK330LC-8J05E / J08E2006-2016
KobelcoSK350-8 / SK350LC-8J05E / J08E2006-2016
KobelcoSK380D-8 Mining Crawler ExcavatorJ05E / J08E2007-2016
Hino500 Series Ranger Heavy TruckJ05E / J08E2006-2016
Hino700 Series Heavy Commercial TruckJ05E / J08E2006-2015
03

Installation, Tightening Torque & Re-torque Protocol

Strict torque compliance is mandatory on Hino J05E / J08E (5.1L / 7.7L) common-rail cylinder heads. Over-torquing stretches the injector body or strips the head clamping threads, while under-torquing allows combustion blow-by past the copper sealing washer:

🔧 Recommended Assembly Torques:
  • Hold-down clamp bolt: 30 N·m (cold state). Always clean the cylinder head recess with an injector seat reamer.
  • High-pressure rail flare nut: 25-30 N·m using a dedicated 17 mm line wrench.
  • Return leak-off banjo bolt: 9-12 N·m with fresh copper washers on both sides of the banjo union.
⚠️ ECU IMA Coding Requirement:

After fitting replacement injectors on Hino J05E / J08E (5.1L / 7.7L), generate or program the cylinder-specific IMA calibration code into the engine ECU using an OEM-level scan tool (Bosch KTS, Renault CLIP, or VAG-COM) to prevent cylinder power imbalance and rough idle.

04

Technical Diagnostics FAQ for Hino J05E / J08E (5.1L / 7.7L)

What DTC fault codes indicate a failing injector on Hino J05E / J08E (5.1L / 7.7L)?

The most frequent fault codes are P0201 through P0204 (Injector Circuit Malfunction on Cylinders 1-4), P2146/P2149 (Injector Group Supply Voltage Error), and P0087 (Fuel Rail Pressure Low due to excessive internal leak-off). Measure solenoid coil resistance across the pins (0.5-1.5 Ω) and perform a graduated-bottle dynamic leak-back test to pinpoint the leaking cylinder.

Can sister SKUs within the Hino J05E / J08E (5.1L / 7.7L) family be interchanged?

Not unless explicitly confirmed on the vehicle build plate. While sister SKUs share the same physical outer envelope and F00RJ02397 control valve, they differ in nozzle spray orifice angle and factory IMA flow calibration. Mixing sister SKUs on the same engine block can trigger rough idle, elevated exhaust gas temperatures (EGT), and MOT emissions failure.

Which specific Bosch injectors fit the Hino J05E / J08E (5.1L / 7.7L) engine?

The verified genuine Bosch common-rail injectors engineered for the Hino J05E / J08E (5.1L / 7.7L) engine family are: