A2740700501
BOSCH A2740700501 Pompă Înaltă Presiune Mercedes C300 E300 GLC300 2.0T M274
2740700501, A2740700401, 0261520215, 0261520216Integrated Solenoid Quantity Control Valve (Flow Metering)-200 barCompatibilitate vehicule și motoare
| Vehicul | Motor | Ani fabricație |
|---|---|---|
| Mercedes-Benz C300 W205 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2015-2021 |
| Mercedes-Benz E300 W213 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2017-2020 |
| Mercedes-Benz GLC300 X253 | Mercedes-Benz M270 / M274 (1.6L & 2.0L BlueDIRECT Turbo) | 2016-2020 |
Specificații tehnice
| Specificație | Valoare |
|---|---|
| Tip sistem | Camshaft-Driven Single-Piston High-Pressure Fuel Pump (HPFP) |
| Presiune de lucruSpecificație de bază | |
| Drive Mechanism | Three-lobe exhaust camshaft actuation with roller tappet bucket |
| Flange Mounting Bolt Torque | 12 N·m (tighten evenly in cross-pattern to prevent housing tilt) |
| High Pressure Line Torque | 27 N·m (high pressure steel flare nut connection) |
| Flow Control Valve ResistanceSpecificație de bază | |
| Coduri de eroare frecvente | P0087 (Fuel Rail Pressure Too Low), P0088 (Fuel Rail Pressure Too High), P0016 (Camshaft Correlation) |
| Workshop Precaution | Inspect roller tappet for wear prior to installation; check engine oil for gasoline dilution odor |
Pompă de înaltă presiune compatibilă (Ansamblu circuit combustibil)
Funcționează pe același circuit de înaltă presiune Common Rail. La cădere de presiune (P0087), verificați debitul pompei înainte de a înlocui injectoarele.
Instrucțiuni de montaj
- [
- {
- "step": 1,
- "title": "Relieve Fuel Line Residual Pressure & Disconnect Battery",
- "instruction": "Disconnect negative battery lead. De-pressurize low-pressure fuel circuit and cover HPFP with shop towels to catch fuel discharge during line disconnection."
- },
- {
- "step": 2,
- "title": "Remove Acoustic Cover & Detach Fuel Flow Control Plug",
- "instruction": "Unclip sound deadening foam around pump housing. Disconnect electrical connector from integrated fuel volume metering solenoid."
- },
- {
- "step": 3,
- "title": "Inspect Camshaft Roller Tappet & Fit New Viton O-Ring",
- "instruction": "Evenly loosen dual flange mounting bolts half-turn at a time. Withdraw HPFP and remove roller tappet. Inspect tappet surface for scuffing and lubricate with fresh engine oil."
- },
- {
- "step": 4,
- "title": "Install HPFP, Torque Mounting Bolts & Reconnect Lines",
- "instruction": "Position HPFP onto cylinder head. Alternately tighten mounting bolts to 12 N·m. Torque high pressure outlet flare nut to 27 N·m. Start engine and verify zero fuel weepage."
- }
- ]
Coduri de Eroare (DTC) si Protocoale de Diagnostic
Coduri comune de eroare de diagnosticare (DTC) declansate atunci cand acest injector common rail sufera uzura, defectiuni de circuit sau abateri:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoale Tehnice de Diagnosticare & Service
Proceduri verificate de atelier, praguri de testare și standarde de intervenție pentru acest ansamblu.