0445110369
Injector VW 2.0 TDI EA189 CFFB CFHC Specs
03L130277J, 03L130277Q, 03L130855CX, 03L130277AC, 03L130277BCF00VC01502DLLA162P21601800 bar peak rail pressureProduct Overview
The Bosch 0445110369 is an OEM CRI2-18 solenoid common rail diesel fuel injector engineered for Volkswagen, Audi, Skoda, and Seat passenger vehicles powered by the Volkswagen Group EA189 (2.0 TDI CFFB / CFHC / CJAA) diesel engine platform. Operating at a peak rail pressure of 1800 bar, this generation features the high-precision DLLA162P2160 8-hole nozzle assembly and F00VC01502 balanced control valve to deliver up to 5 micro-injections per combustion cycle, meeting Euro 5 emissions standards. Direct OEM replacement for VAG references 03L130277J, 03L130277Q, 03L130855CX, 03L130277AC, and Bosch remanufactured exchange units 0986435166 / 0986435167 / 0986435214. For comprehensive engine family interchange and technical specifications, explore the [VW 2.0 TDI EA189 Engine Family Hub](/diesel-injector/ea189-2-0-tdi/).
Always verify the OE reference laser-etched on your failed injector body (03L130277J / 03L130277Q) prior to installation. Bosch 0445110369 utilizes the F00VC01502 control valve and DLLA162P2160 nozzle assembly calibrated to 1800 bar. Cylinder-specific 7-digit IMA coding into the EDC17 ECU is mandatory after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf 6 / Passat B7 / Tiguan / Touran 2.0 TDI | Volkswagen EA189 2.0 TDI (CFCA / CFFB / CFHC) | 2009-2015 |
| Audi A3 (8P) / Q3 2.0 TDI | Volkswagen EA189 2.0 TDI (CFCA / CFFB / CFHC) | 2009-2015 |
| Skoda Octavia II / Superb II / Yeti 2.0 TDI | Volkswagen EA189 2.0 TDI (CFCA / CFFB / CFHC) | 2009-2015 |
| Seat Leon II / Altea / Alhambra 2.0 TDI | Volkswagen EA189 2.0 TDI (CFCA / CFFB / CFHC) | 2009-2015 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 0445110369 |
| Brand | Volkswagen / Audi / Skoda / Seat / BOSCH |
| Type | Complete Injector Assembly (Bosch Common Rail (CRI2-18 solenoid)) |
| OE Number | 03L130277J |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Nozzle Part NumberCore Spec | |
| Magnet Assembly | F00VC30053 |
| Seal Ring Kit | F00VP01004 |
| Injection System | Bosch Common Rail (CRI2-18 solenoid) |
| Operating PressureCore Spec | |
| Torque Spec | 28 N·m |
| Hold Down Torque | 8 N·m + 90° |
| Warranty | 12 Months |
| Emission Standard | Euro 5 |
| Engine Family | VW 2.0 TDI EA189 (CFFB / CFHC) |
| Coding Required | Yes (IMA Code) |
Installation Tips
Tools needed: 10mm & 11mm flare nut wrench (rail and injector inlet unions), Injector slide hammer / mechanical puller kit (if carbon seized), Injector seat cleaning brass brush set & industrial vacuum, Seat reaming tool (if carbon erosion is present), Torque wrench (2 N·m - 40 N·m range), VCDS / ODIS / Autel diagnostic scan tool with 7-character IMA coding capability, Digital micrometer / depth gauge for copper washer check
- Disconnect Battery & Relieve Rail Pressure: Isolate negative battery terminal and verify rail residual pressure drops below 10 bar via live diagnostics before cracking fuel fittings.
- Clean Engine Bay & Injector Recesses: Thoroughly blast away grit, oil slurry, and loose dirt around cylinder head injector wells using compressed air and degreasing solvent.
- Label Wiring Harness & Spill-Off Connectors: Tag each cylinder harness connector and gently disengage delicate plastic spill-off return rail clips.
- Remove High-Pressure Supply Lines: Back off high-pressure union nuts with a flare-nut wrench; IMMEDIATELY cap all open fuel rail orifices and injector inlets with clean blanking caps.
- Extract Hold-Down Clamp Fasteners: Back out hold-down clamp bolts. Note that torque-to-yield stretch bolts must always be discarded and never reused.
- Extract Injector Body: Withdraw injector vertically. If carbon-bonded or coked, attach an approved mechanical slide-hammer puller to the inlet adaptor without rotating the injector body.
- Inspect Injector Well & Bore: Ensure old copper seal washer has not remained fused at the base of the cylinder head seat; remove with a brass retrieval pick if stuck.
- Clean & Ream Injector Seat: Ream and burnish injector seating face using dedicated seat cutter brushes and industrial vacuum until seat is 100% bare, flat metal.
- Install New Copper Sealing Washer: Mount an OEM-specification copper washer (1.50mm thickness, pure annealed copper) using clean motor oil or high-temp grease to hold in position.
- Fit Injector with Ceramic Anti-Seize: Lightly coat the injector body barrel with approved high-temperature ceramic grease; keep nozzle tip and copper washer strictly dry and clean.
- Torque Hold-Down Clamp to Spec: Secure hold-down clamp bolts and torque to factory specified stages (8 N·m + 90°) using a calibrated torque wrench.
- Refit High-Pressure Delivery Pipes: Thread union nuts by hand to avoid cross-threading, then tighten injector inlet and rail unions to 28 N·m evenly using a torque wrench.
- Reconnect Return Leak-Off Line & Harness: Push on leak-off return clips until retaining collars click home; reattach electrical plug and lock harness tab firmly.
- ECU IMA / QR Code Calibration & Fuel Priming: Program the unique 7-character alphanumeric IMA calibration code laser-etched on the injector head into the corresponding EDC17 ECU cylinder address; prime fuel system prior to initial cranking.
- CRITICAL IMA CALIBRATION: Never operate the EA189 engine without programming the new 7-digit IMA trim code into the EDC17 ECU — uncalibrated injectors cause combustion knocking, cylinder imbalance, and premature DPF clogging. Check our [IMA Injector Coding Guide](/knowledge/ima-coding/) and [IMA Coding Verification Tool](/tools/injector-coding/).
- CRITICAL COPPER WASHER REPLACEMENT: Always install brand new 1.50mm copper crush washers and torque-to-yield clamp bolts — reusing old seals leads to catastrophic combustion gas leakage ('black death' buildup).
- HOSPITAL-GRADE FUEL CLEANLINESS: A microscopic contamination particle as small as 5 microns can jam the internal F00VC01502 valve or needle — ensure all fuel line protective plugs stay on until final connection.
- STRICT HOLD-DOWN TORQUE: Adhere strictly to the 8 N·m + 90° tightening sequence — overtightening distorts the injector body and binds the needle. Review full torque values in our [Diesel Injector Torque Specs Guide](/knowledge/torque-specs/).
Frequently Asked Questions
Does Bosch injector 0445110369 require ECU coding (IMA code)?
Yes, Bosch injector 0445110369 requires cylinder-specific IMA calibration code programming into the Bosch EDC17 engine control unit (ECU). Each unit has a unique 7-character alphanumeric calibration code laser-etched on its electrical connector body that defines fuel delivery tolerances across multiple rail pressure points (pre-injection, main injection, and post-injection). Programming this code via a diagnostic tool (VCDS, ODIS, or Autel MaxiSys) is mandatory to ensure balanced cylinder idle, proper emissions compliance, and smooth throttle response.
What are the most common symptoms of a failing 0445110369 injector on VW 2.0 TDI EA189?
Common failure symptoms include prolonged cold-start cranking, rough or hunting idle, black exhaust smoke under acceleration (nozzle needle wear/over-fueling), white smoke on startup (unburnt fuel spray), combustion knocking under load, increased fuel consumption, cylinder balance deviations exceeding +/- 1.5 mg/stroke, and high dynamic spill-off return rates causing low rail pressure DTC P0087 under hard acceleration.
Should I replace 0445110369 injectors individually or as a complete set?
While replacing a single failed injector is acceptable if fuel contamination is ruled out, industry best practice on VAG 2.0 TDI engines with over 150,000 km is to replace or bench-test all 4 injectors as a complete set. Wear across the high-pressure control valve (F00VC01502) and nozzle (DLLA162P2160) occurs evenly across all cylinders; fitting one new unit alongside three worn units often leads to noticeable idle vibration due to delivery quantity variance.
Why must the copper crush washer and hold-down bolt be replaced on every install?
The copper washer forms the critical gas-tight seal between the injector nozzle and the cylinder head combustion chamber. During combustion, temperatures exceed 1,500°C and pressures surpass 150 bar. A compressed washer work-hardens and will not re-seal properly. Furthermore, EA189 hold-down clamp bolts are torque-to-yield (stretch) fasteners (8 N·m + 90°) designed for single use; reusing them risks bolt snapping inside the cylinder head or loss of clamp tension, leading to blow-by carbon accumulation.
What preventative maintenance is required after installing replacement 0445110369 injectors?
Always replace the diesel fuel filter with an OEM-spec filter (3 to 5 micron rating), inspect the fuel filter canister for metallic swarf from high-pressure pump (CP4) wear, bleed and prime the common rail using diagnostic software before cranking, use high-quality EN590 diesel, and verify injector smooth running balance values with VCDS after 500 km of driving.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.