BOSCH 0445110429
Common Rail Injector for VW Transporter T5/T6 / Amarok 2.0 BiTDI CFCA 132kW
03L130277A, 03L130277CF00VC01502DLLA162P21601600 bar peak rail pressureProduct Overview
The Bosch 0445110429 is an electro-hydraulic Common Rail Injector (CRI) engineered for passenger car diesel applications requiring Euro 4 emissions compliance. Operating at dynamic rail pressures up to 1600 bar, this unit utilizes an optimized electromagnetic solenoid actuator paired with a high-precision valve group to achieve micro-second multi-pulse injection metering, including pilot, main, and post-injection events. Utilizing nozzle 0433172160 and control valve F00VC01502, it delivers finely atomized spray geometry that optimizes thermodynamic combustion efficiency while suppressing particulate formation and engine acoustics.
Cross-reference the cylinder head build plate with OE numbers 03L130277A or 03L130277C before installation, and ensure the unique alphanumeric IMA trim code is calibrated into the engine ECU to prevent severe cylinder misfire and dynamic balancing errors.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Transporter / Caravelle / Multivan (T5.1/T6) | CFCA / CFFB / CFHC | 2009-2016 |
| Volkswagen Amarok 2.0 BiTDI | CFCA / CFFB / CFHC | 2010-2016 |
| Volkswagen Crafter 2.0 BiTDI | CFCA / CFFB / CFHC | 2011-2016 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 0445110429 |
| Brand | BOSCH |
| Product Type | Complete Solenoid Common Rail Injector Assembly |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Engine Family | EA189 (2.0 BiTDI CFCA) |
| Operating PressureCore Spec | |
| Emission Standard | Euro 4 |
Installation Tips
- Execute a mandatory two-wrench counter-hold technique during high-pressure pipe connection; secure the injector fuel inlet fitting with an open-end counter-hold wrench while tightening the high-pressure union nut to 28 N·m to prevent torsional shearing of the internal control valve spindle and internal alignment dowels.
- Meticulously clean the cylinder head injector bore down to base metal using an approved brass seating tool, install a new annealed copper sealing washer, and apply a thin film of high-temperature non-metallic ceramic anti-seize paste strictly to the injector body shaft, ensuring zero paste contaminates the nozzle tip or spray orifices.
- Secure the hold-down clamp bolt to factory specification of 8 N·m + 90° angle rotation. Program the specific alphanumeric IMA classification code printed on the solenoid magnet cap into the engine control module using an advanced diagnostic scan tool, then perform a manual low-pressure fuel circuit prime before initial cranking to prevent dry-friction scuffing of internal valve seats.
- Match part number 0445110429 and the listed cross references before ordering or fitting.
- Torque the mounting / hold-down to 8 N·m + 90°.
- Torque the high-pressure line to 28 N·m.
Frequently Asked Questions
What is the OE cross-reference for this injector?
This injector corresponds directly to VAG original equipment manufacturer part numbers 03L130277A and 03L130277C for Common Rail Diesel Injection platforms.
What control valve / actuator is used?
Dynamic fuel discharge is governed by control valve F00VC01502, operated by a high-speed electromagnetic solenoid actuator coupled to nozzle 0433172160.
Does this injector require ECU IMA coding?
Yes, ECU IMA (Injector Quantity Adjustment) coding is mandatory. The laser-etched alphanumeric calibration code contains flow-rate tolerance parameters that the engine control unit requires to balance per-cylinder fuel delivery; failure to program this code leads to uneven idle, cylinder knock, and increased exhaust emissions.
What are the common failure symptoms and associated DTC codes?
Common symptoms include extended cranking, hard or no-start conditions, severe engine knocking, and loss of power under acceleration. Typical diagnostic trouble codes include P0201 through P0204 (injector circuit open/short), P0087 (rail pressure too low due to worn control valve seats allowing excessive back-leakage), and cylinder balance deviations such as P1011 or P1012.
What are the proper installation torque specifications?
The injector hold-down clamp stretch bolt must be replaced and torqued to OE specifications of 8 N·m + 90° angle rotation. The high-pressure fuel line union nut must be torqued to 28 N·m using a secondary wrench to counter-hold the inlet fitting.
How do you perform a dynamic back-leakage flow bench test?
Mount the injector on an ISO-compliant calibration test bench and evaluate fuel return volumes across operating pressure ranges up to 1600 bar. Nominal idle back-leakage should not exceed 35 ml/min, and maximum full-load leak-off must remain under 50 ml/min; excessive back-leakage beyond these thresholds indicates valve seat erosion on control valve F00VC01502, requiring internal component replacement.
What is the acceptable solenoid coil electrical resistance?
At an ambient temperature of 20°C (68°F), the solenoid coil resistance measured across the two electrical terminal pins must register between 0.25 and 0.50 ohms. Additionally, an insulation resistance test from either pin to the injector body ground should yield infinite resistance (>10 Megohms).
Why is the two-wrench installation procedure strictly mandatory?
Applying tightening torque to the high-pressure fuel rail line nut without a counter-holding wrench on the inlet adapter transfers rotational shear forces through the injector body. This torsional stress shears the internal dowel alignment pins, twists the precision-seated control valve spindle assembly, disrupts the internal high-pressure seal faces, and permanently ruins the injector.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.