Catalog / BOSCH / 0445110146
BOSCH

BOSCH 0445110146

View Specs
SolenoidCommon Rail Diesel SystemEuro 4

Common Rail Injector for F9Q 762

Reference data for BOSCH 0445110146 common rail injector · OEM 8200238528, 8200212716, 7700111014, 8200389369, 93169139 · Application Renault F9Q 1.9 dCi (1870 cc)
OE REFERENCE8200238528, 8200212716, 7700111014, 8200389369, 93169139
CONTROL VALVEF00VC01005
NOZZLEDSLA140P862+
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Bosch 0445110146 is a second-generation solenoid Common Rail Injector (CRI) engineered for passenger car and light commercial direct-injection applications, notably Renault and Opel 1.9 dCi/CDTI platforms powered by the F9Q 762 engine. Operating at system peak dynamic pressures up to 1600 bar, the unit utilizes precision hydraulic staging to deliver micro-second multi-pulse injection events—enabling pilot, main, and post-injection strategies. Combined with control valve assembly F00VC01005 and nozzle assembly 0433175230, this platform delivers precise fuel atomization to minimize combustion noise, optimize torque, and ensure strict compliance with Euro 4 emission standards.

Before You Order

Technicians must cross-verify the vehicle build plate against OE cross-references (Renault 8200238528 / Opel 93169139) and execute mandatory alphanumeric IMA trim coding within the engine control unit to prevent rough idle and cylinder unbalance.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Renault Laguna II / Megane II / Scenic IIF9Q2001-2008
Renault Espace IV / Trafic IIF9Q2001-2014
Opel Vivaro AF9Q2001-2014
Nissan PrimastarF9Q2001-2014
04

Technical Specifications

SpecificationValue
SKU0445110146
BrandBOSCH
Product TypeComplete Solenoid Common Rail Injector Assembly
Control ValveCore Spec
🔗 Shared Valve (3 assemblies):04451100210445110056
Nozzle CodeCore Spec
🔗 Shared Nozzle (3 assemblies):04451100210445110056
Engine FamilyF9Q 1.9 dCi (88 kW / 120 HP)
Operating PressureCore Spec
Emission StandardEuro 4
Magnet AssemblyF00VC30055
Seal Ring KitF00VC99002
05

Installation Tips

  1. Strictly adhere to the two-wrench counter-hold procedure when connecting the high-pressure fuel line: apply a 14 mm open-end backing wrench directly to the injector inlet hex while tightening the line union nut with a 17 mm flare crowfoot wrench to exactly 25–28 N·m, preventing internal valve spindle distortion and body thread shearing.
  2. Clean the cylinder head injector well down to bare metal using a brass wire seat reamer, install a replacement copper sealing washer from Seal Ring Kit F00VC99002, and apply a thin coating of high-temperature non-metallic ceramic anti-seize paste exclusively along the injector body shaft, ensuring no paste contacts the nozzle tip or washer seating surface.
  3. Program the specific alphanumeric IMA code laser-etched onto the solenoid cap into the diagnostic scan tool for the corresponding cylinder, then manually bleed and prime the low-pressure fuel circuit prior to starter engagement to protect internal valve surfaces from dry-crank galling.
Tips & Warnings:
  • Tighten the injector hold-down to 25-30 N·m.
  • Tighten the high-pressure line to 28-30 N·m.
  • Verify part number 0445110146 or the listed cross references and confirm F9Q fitment in the vehicle’s EPC before installation.
06

Frequently Asked Questions

QWhat is the OE cross-reference for this injector?

The Bosch 0445110146 injector cross-references directly to Renault OE numbers 8200238528, 8200212716, 7700111014, and 8200389369, as well as General Motors / Opel / Vauxhall OE number 93169139 for 1.9 dCi/CDTI (F9Q 762) engines.

QWhat control valve / actuator is used?

This injector utilizes hydraulic control valve assembly F00VC01005 coupled with solenoid coil magnet assembly F00VC30055. The electromagnetic actuator modulates pressure in the control chamber to drive needle actuation via nozzle assembly 0433175230.

QDoes this injector require ECU IMA coding?

Yes, ECU IMA (Injector Quantity Adjustment) coding is mandatory. The unique alphanumeric calibration code etched on the plastic solenoid connector head specifies exact injector micro-tolerances across low, mid, and high rail pressure zones; failure to register this code will cause injection volume drift, uneven idle balance, and high exhaust emissions.

QWhat are the common failure symptoms and associated DTC codes?

Common symptoms include hard starting (especially when warm), engine misfiring, excessive black or gray smoke, and limp-home mode activation. Typical diagnostic fault codes include P0087 (Fuel Rail/System Pressure Too Low due to excessive back-leakage past a worn valve seat), P0201 through P0204 (Injector Circuit Open/Short on Cylinders 1-4), and cylinder contribution/balance trouble codes such as P1011 or P1012.

QWhat are the proper installation torque specifications?

Secure the cylinder head hold-down clamp bolt to the manufacturer specification of 25-30 N·m (or stage 1: 6 N·m followed by final clamp torque of 18-20 N·m depending on chassis fastener type). The high-pressure inlet feed line nut requires 25-28 N·m while using a counter-hold backing wrench on the inlet body hex.

QHow do you perform a dynamic back-leakage flow bench test?

Install the unit on an ISO 4113-compliant common rail test bench at a calibration fluid temperature of 40°C. Measure the volumetric leak-off: at low-pressure idle conditions (250–300 bar), maximum permissible return flow must not exceed 35 ml/min; at maximum dynamic load (1600 bar), return back-leakage must not exceed 50 ml/min. Higher values indicate internal ball seat erosion within control valve F00VC01005.

QWhat is the acceptable solenoid coil electrical resistance?

The internal resistance of electromagnetic solenoid assembly F00VC30055 must measure between 0.25 and 0.50 ohms across the two electrical pins at 20°C (68°F). Measured insulation resistance between either terminal pin and the metallic injector chassis must exceed 100 megaohms at 500V DC.

QWhy is the two-wrench installation procedure strictly mandatory?

Bosch CRI solenoid injectors feature internal threaded joints and locating pins holding the control valve and spindle in strict micron-tolerance alignment. Torquing the high-pressure fuel supply pipe without counter-holding the inlet fitting transmits rotational shear forces directly into the injector body, permanently damaging internal seal lands, shearing alignment dowels, and causing high-pressure external or internal fuel leakage.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0302Critical

Cylinder 2 Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol