BOSCH 0445115077
Piezo Common Rail Injector for BMW 330d / 530d / X5 3.0d M57N2
13537808089, 13537808094, 13537797877, 13537796042, 13537796043, 13537805686, 13537807209, 13537809194INTEGRATED PIEZO ACTUATOR (CRI3)F00VX400211600 bar peak rail pressureProduct Overview
The Bosch 0445115077 is an OEM common rail diesel fuel injector engineered for BMW passenger vehicles powered by the M57N2 / M57D30TÜ2 (3.0d 6-cylinder inline, 170-210 kW / 231-286 hp) diesel engine. Operating at a peak rail pressure of 1600 bar, this unit features the high-precision F00VX40021 piezo nozzle assembly and Integrated Piezo Actuator (CRI3) valve mechanism to deliver multiple micro-injections per combustion cycle. It fully complies with Euro 4 emissions standards. Direct replacement for OEM references 13537808089, 13537808094, 13537797877, 13537796042, 13537796043, 13537805686, 13537807209, 13537809194, and Bosch exchange 0986435359.
Always verify the OE cross-reference stamped on your failed injector body (13537808089 / 13537796043 / 13537809194) prior to ordering. Bosch 0445115077 utilizes the Integrated Piezo Actuator (CRI3) valve mechanism and F00VX40021 piezo nozzle assembly calibrated to 1600 bar for BMW M57N2 engines. Cylinder-specific IMA coding is mandatory after installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| BMW 3 Series (E90/E91/E92/E93) | M47 / M57 / M47N / M57N / 204D4 / 306D2 | 2005-2010 |
| BMW 5 Series (E60/E61) | M47 / M57 / M47N / M57N / 204D4 / 306D2 | 2005-2010 |
| BMW X3 (E83) | M47 / M57 / M47N / M57N / 204D4 / 306D2 | 2006-2010 |
| BMW X5 (E70) | M47 / M57 / M47N / M57N / 204D4 / 306D2 | 2006-2010 |
| BMW X6 (E71) | M47 / M57 / M47N / M57N / 204D4 / 306D2 | 2007-2010 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 0445115077 |
| Brand | BMW / BOSCH |
| Type | Complete Injector Assembly (Bosch Common Rail (CRI3-16 piezo)) |
| OE Number | 13537808089 |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Nozzle Part NumberCore Spec | |
| Injection System | Bosch Common Rail (CRI3-16 piezo) |
| Operating PressureCore Spec | |
| Torque Spec | 28-30 N·m |
| Hold Down Torque | 9 N·m + 90° |
| Warranty | 12 Months |
| Emission Standard | Euro 4 |
| Engine Family | M57N2 / M57D30TÜ2 (3.0d 6-Cyl) |
| Coding Required | Yes (IMA Code) |
Installation Tips
Tools needed: 10mm & 11mm flare nut wrench (rail and injector inlet unions), Injector slide hammer / mechanical puller kit (if seized), Injector seat cleaning brass brush set & industrial vacuum, Seat reaming tool (if carbon erosion is present), Torque wrench (2 N·m - 40 N·m range), ECU diagnostic scan tool with IMA/QR coding capability, Digital micrometer / depth gauge for copper washer check
- Disconnect Battery & Relieve Rail Pressure: Isolate negative battery terminal and verify rail residual pressure drops below 10 bar via live diagnostics before cracking fuel fittings.
- Clean Engine Bay & Injector Recesses: Thoroughly blast away grit, oil slurry, and loose dirt around cylinder head injector wells using compressed air and degreasing solvent.
- Label Wiring Harness & Spill-Off Connectors: Tag each cylinder harness connector and gently disengage delicate plastic spill-off return rail clips.
- Remove High-Pressure Supply Lines: Back off high-pressure union nuts with a flare-nut wrench; IMMEDIATELY cap all open fuel rail orifices and injector inlets with clean blanking caps.
- Extract Hold-Down Clamp Fasteners: Back out hold-down clamp bolts. Note that torque-to-yield stretch bolts must always be discarded and never reused.
- Extract Injector Body: Withdraw injector vertically. If carbon-bonded or coked, attach an approved mechanical slide-hammer puller to the inlet adaptor without rotating the injector body.
- Inspect Injector Well & Bore: Ensure old copper seal washer has not remained fused at the base of the cylinder head seat; remove with a brass retrieval pick if stuck.
- Clean & Ream Injector Seat: Ream and burnish injector seating face using dedicated seat cutter brushes and industrial vacuum until seat is 100% bare, flat metal.
- Install New Copper Sealing Washer: Mount an OEM-specification copper washer of designated thickness using high-temp grease to hold in position.
- Fit Injector with Ceramic Anti-Seize: Lightly coat the injector body barrel with approved high-temperature ceramic grease; keep nozzle tip and copper washer strictly dry and clean.
- Torque Hold-Down Clamp to Spec: Secure hold-down clamp bolts and torque to factory specified stages (9 N·m + 90°) using a calibrated torque wrench.
- Refit High-Pressure Delivery Pipes: Thread union nuts by hand to avoid cross-threading, then tighten injector inlet and rail unions to 28-30 N·m evenly.
- Reconnect Return Leak-Off Line & Harness: Push on leak-off return clips until retaining collars click home; reattach electrical plug and lock harness tab firmly.
- ECU IMA / QR Code Calibration & Fuel Priming: Program the unique alphanumeric IMA/QR calibration code etched on the injector head into the corresponding ECU cylinder address; prime fuel system prior to initial cranking.
- CRITICAL IMA CALIBRATION: Never operate the engine without programming the new IMA/QR trim code into the ECU map — uncalibrated injectors cause combustion knocking, cylinder imbalance, and premature DPF clogging.
- CRITICAL COPPER WASHER REPLACEMENT: Always install brand new copper crush washers and torque-to-yield clamp bolts — reusing old seals leads to catastrophic combustion gas leakage ('black death' buildup).
- HOSPITAL-GRADE FUEL CLEANLINESS: A microscopic contamination particle as small as 5 microns can jam the internal piezo valve or needle — ensure all fuel line plugs stay on until final connection.
- STRICT HOLD-DOWN TORQUE: Adhere strictly to the 9 N·m + 90° tightening sequence — overtightening distorts the injector body and binds the needle.
Frequently Asked Questions
Does Bosch injector 0445115077 require ECU coding (IMA / QR code)?
Yes, Bosch injector 0445115077 requires cylinder-specific IMA calibration code programming into the BMW DDE engine control unit. Each unit has a unique multi-character calibration code stamped on its electrical connector body that defines fuel delivery tolerances across multiple rail pressure points. Programming this code via a diagnostic scanner (BMW INPA, ISTA/D, or Autel MaxiSys) is mandatory to ensure balanced cylinder idle, proper emissions compliance, and smooth throttle response.
What are the most common symptoms of a failing 0445115077 injector on BMW M57N2 (3.0d 6-Cyl)?
Common symptoms include prolonged cold-start cranking, rough or oscillating idle, black exhaust smoke under acceleration (nozzle needle wear/over-fueling), ticking/clattering under load, increased fuel consumption, cylinder misfire trouble codes (P0300-P0306), and high fuel spill-off return rates causing low rail pressure codes under heavy acceleration.
What is the difference between CRI2 solenoid (0445110080) and CRI3 piezo (0445115077) on BMW M57 engines?
The earlier Euro 3 / Euro 4 M57N engines utilized CRI2 solenoid injectors (such as 0445110080 / 0445110131) with electromagnetic solenoid valves. Later M57N2 / M57D30TÜ2 engines upgraded to Bosch CRI3 piezo injectors (0445115077) featuring piezoelectric crystal stacks and nozzle assembly F00VX40021 for rapid multi-pulse fuel delivery. The two families are electronically and hydraulically incompatible.
Why must the copper crush washer and hold-down bolt be replaced on every install?
The copper washer forms the critical gas-tight seal between the injector nozzle and the cylinder head combustion chamber. During combustion, temperatures exceed 1,500°C and pressures surpass 150 bar. A compressed washer work-hardens and will not re-seal properly. Furthermore, BMW hold-down clamp bolts are torque-to-yield stretch fasteners designed for single use; reusing them risks bolt snapping inside the cylinder head.
What preventative maintenance is required after installing replacement 0445115077 injectors?
Always replace the diesel fuel filter with a high-efficiency OEM-spec filter (3 to 5 micron rating), inspect the fuel tank and fuel lines for metallic swarf from high-pressure pump wear, flush the common rail if debris is present, use high-quality EN590 diesel, and verify injector smooth running balance values with diagnostic software after 500 km of driving.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.